Because of an error in data encryption, this session will end. Please try connecting to the remote computer again.

Cause:  Data encryption provides security for data
traveling over network connections. A data encryption error can end a
session for security reasons.

Solution:  Try connecting to the remote computer again. Encryption policies can vary between systems and domains.

The remote connection has timed out. Please try connecting to the remote computer again.

Cause:  The terminal server disconnected your
session because you did not send a response within the time limit set
for responses.

Solution:  Try connecting to the terminal server again. If you receive this error message, try to reconnect at a later time.

Cause:  A slow network connection, caused by excessive network traffic, has delayed your response to the terminal server.

Solution:  Try connecting to the terminal server again. If you receive this error message, try to reconnect at a later time.

The remote session was disconnected because the total logon time
limit was reached. This limit is set by the server administrator or by
network policies.

Cause:  Your connection to the terminal server exceeded the time limit.

Solution:  Try connecting to the terminal server
again. If you receive this error message, try to reconnect at a later
time.  The server administrator may need to review the length of
time allowed for connections before they expire.

The specified computer name contains invalid characters. Please verify the name and try again.

Cause:  The name of the remote computer is incorrect. This might be a typing error.

Solution:  Try typing the name of the remote
computer again. If you receive the same message, contact the server
administrator to be sure you are using the correct name for the remote
computer.

The specified remote computer could not be found. Verify that you
have typed the correct computer name or IP address, and then try
connecting again.

Cause:  The name or IP address of the remote computer is incorrect. This might be a typing error.

Solution:  Try typing the name or IP address of the
remote computer again. If you receive the same message, contact the
server administrator to be sure you are using the correct name or IP
address for the remote computer.

The remote session to the remote computer was ended by means of an
administration tool. Your administrator might have ended your
 connection.

Cause:  The most common cause of this error is that
the server administrator needed to perform maintenance tasks on the
terminal server. These tasks can be performed only when there are no
remote connections to the terminal server.

Solution:  Try to reconnect at a later time.

The remote session was disconnected because your session was logged
off at the remote computer. Your administrator or another user might
have ended your session.

Cause:  The most common cause of this error is that
the server administrator needed to perform maintenance tasks on the
terminal server. These tasks can be performed only when there are no
remote connections to the terminal server.

Solution:  Try to reconnect at a later time.

The remote session was disconnected because another user has connected to the session.

Cause:  The most common cause of this error is that
the server administrator needed to perform maintenance tasks on the
terminal server. These tasks can be performed only when there are no
remote connections to the terminal server.

Solution:  Try to reconnect at a later time.

The remote session was disconnected because the total logon time
limit was reached. This limit is set by the server administrator or by
network policies.

Cause:  Your connection to the terminal server exceeded the time limit set.

Solution:  Try connecting to the remote computer
again. If you receive the same message, try to reconnect at a later
time. The server administrator may need to review the length of time
allowed for connections before they expire.

The local computer is low on memory. Close some programs, and then connect to the remote computer again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  Close all unnecessary programs, and try your connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by:

The connection was ended because of a network error. Please try connecting to the remote computer again.

Cause:  A network error prevented your computer from communicating with the terminal server.

Solution:  Try connecting to the remote computer
again. If you receive the same message, be sure that your computer is
connected to the network.

The client could not connect. You cannot connect to the console from a console session of the same computer.

Cause:  You are logged on to a computer and you are trying to connect to that same computer.

Solution:  If you are not on the same computer, contact the server administrator.

The client could not connect to the remote computer. Remote
connections might not be enabled or the computer might be too busy to
accept new connections. It is also possible that network problems are
preventing your connection. Please try your connection again later. If
the problem continues to occur, contact your administrator.

Cause:  The remote computer might not be set up to accept remote connections.

Solution:  Try connecting to the remote computer at a later time.

Cause:  The remote computer might already have the maximum number of remote connections it is set up to accept.

Solution:  Try connecting to the remote computer at a later time.

Cause:  Network problems might be preventing the connection.

Solution:  Try connecting to the remote computer at a later time.

Error: Out of memory. The remote session will be disconnected.
Close some programs on the local computer, and then try connecting to
the remote computer again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  Close all unnecessary programs, and try your connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by:

An internal state error has occurred. The remote session will be
disconnected. Your local computer might be low on memory. Close some
programs, and then try connecting to the remote computer again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  The system load will need to be brought down and memory freed up before
a connection can be made. Close all unnecessary programs, and try your
connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by:

Because of a protocol error, this session will be disconnected. Please try connecting to the remote computer again.

Cause:  A protocol specifies the way a computer
communicates with other computers. A protocol error prevents your
computer from communicating with the terminal server to which you were
 connected.

Solution:  Try connecting to the remote computer again.

Because of a protocol error (error_code), the remote session will
be disconnected. Please try connecting to the remote computer again.

Cause:  A protocol specifies the way a computer
communicates with other computers. A protocol error prevents your
computer from communicating with the terminal server to which you were
 connected.

Solution:  Try connecting to the remote computer again.

Because of a security error, the client could not connect to the
remote computer. Verify that you are logged on to the network, and then
try connecting again.

Cause:  The most common causes are network errors or slowdowns.

Solution:  Be sure your computer is connected to the network. Try to reconnect at a later time.

The remote session was disconnected because the remote computer is low on memory.

Cause:  Memory errors have a variety of causes, but
the result is the same. The remote computer does not have enough memory
to start and maintain the connection you are attempting to make.

Solution:  The system load will need to be brought down
and memory freed up before a connection can be made. Close all
unnecessary programs, and try your connection again.

Because of an unknown error, the remote session will be
disconnected. The local computer might be low on memory. Close some
programs, and then try connecting to the remote computer again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  The system load will need to be brought down and memory freed up before
a connection can be made. Close all unnecessary programs, and try your
connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by:

An unrecoverable error occurred while the client was attempting to
connect. Close some programs, and then try connecting to the remote
computer again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  The system load will need to be brought down and memory freed up before
a connection can be made. Close all unnecessary programs, and try your
connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by:

An error occurred when the client attempted to connect to the
remote computer. Check your system memory and then try the connection
 again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  The system load will need to be brought down and memory freed up before
a connection can be made. Close all unnecessary programs, and try your
connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by:

Unable to allocate window resources. The remote session will be
disconnected. Close some programs on the local computer, and then try
connecting to the remote computer again.

Cause:  Not enough RAM available on your computer.
If your computer has too little RAM available, it cannot free enough
processing capacity to start new functions, such as applications or
 connections.

Solution:  The system load will need to be brought down and memory freed up before
a connection can be made. Close all unnecessary programs, and try your
connection again.

Cause:  Not enough disk space available on your
hard drive. If the hard drive on your computer is full, there might not
be enough space available to allow the swap file to operate correctly.
The swap file allows your computer to perform some RAM functions even
when there is not enough RAM space available.

Solution:  Free some space on your hard drive by: